If you love off-roading, you will need to protect your vehicle from rocks and rough terrain. The best way to do this is with a rock slider. Rock sliders are used mainly by off-roaders when their vehicle slides off the track and hits rocks or other hard surfaces. It will protect the car's doors and frame and make it easier to climb in and out of the vehicle. It's easy to see rock sliders on trucks or SUVs because they have slightly higher ground clearance than most cars. DIY Rock Sliders Plans can be done with different materials, including metal, wood, and aluminum. However, the first step in making a DIY rock slider is to create a plan for it. Making a proper plan will help you get the right parts and start your project immediately without wasting time.
Making DIY Rock Sliders can be a complicated process if you are unsure how to go about it. If you are not a DIYer, it is advisable to seek the services of a professional who will do the job for you. However, you can make your rock slider at home without much trouble with the right tools and motivation. Making a rock slider on your own is fun and saves you money. Don't forget to work safely in your workshop and wear protective gear when necessary. There are different kinds of sliders depending on your vehicle type. Some vehicles have low clearance and therefore need more protection than others. The following are 18 DIY Rock Slider Plans to help you make one for your vehicle. Start building today!
How To Build Rock Sliders
Your vehicle will take a beating when you're on the trails or out in the middle of nowhere. Sliders are there to protect your vehicle from being damaged and protect you from being injured. We'll show you how to build rock sliders for your vehicle. Determine what type of metal to use for strength and weight reduction. If it is a tube frame vehicle, simple tube frame sliders are needed. But if it is a chassis frame vehicle, two or three-inch boxed steel may be required. Ensure that the metal used is sturdy enough to handle the abuse they will take and light enough to not add too much additional weight to the vehicle, which may negatively affect driveability.
DIY Rock Sliders Build
Making rock sliders is a straightforward and effective way to protect the sills of your jeep. These rock sliders are made from square tubing, metal plate, and high-resistance rostellum Paint. After gathering the necessary materials, the next task is measuring how long a pair of sliders need to be. These measurements can vary for each vehicle. You can check the link below for measurements taken on other vehicles.
How To Add Simple Steps To Rock Sliders
Rock sliders are a significant step on your vehicle, especially if there is any off-road activity. Rock sliders help protect the sides of a vehicle and make injuries less likely in case of an accident or a leg getting stuck under a rock or something else. However, a standard rock slider will only have one step, which can be tall and difficult for shorter people to use. In this video tutorial, you'll learn how to add simple steps to the rock slider. These steps will make it easier for shorter people to climb up onto the rock slider and get into the vehicle should they need to be carried out after an accident.
Rock Sliders DIY
You will need a rectangular steel tube that is 50mm×50mm×3 mm thick during the construction of this project. You may use any other materials that are available in your working place. The design for the project looks perfect, but you can make minor changes to suit your needs and fabricate the task quickly. The step-by-step instructions with pictures help you know more about the project. Moreover, you will understand how your car's body works, an added advantage to this project.
Toyota Hilux Rock Sliders DIY
This is a video of making a universal rock slider out of steel pipe for a Toyota Hilux. The pipe size is 40NB, about 300mm in diameter, and is available at any hardware store. A gasless MIG welding machine is used for welding the pipes together, but you could also use an arc welder. Rock sliders are not beginner-level builds and require some basic fabrication skills. This video serves as an introduction to the concepts needed for rock slider fabrication.
DIY Rock Sliders
The DIY rock slider is a perfect solution to save money without compromising quality. It can be created within a few hours and with only essential tools. The rock slider consists of pre-bent and pre-cut metal tubes. You need to weld them together and mount them to vehicles. The tubes need to come up the side of the vehicles, curve down and over, and then come back up on the other side of the vehicles. This is an old cowhand trick, but it does hold out a lot of rocks. It is also easier for you to see around your vehicle, making for safer driving.
How To Make Homemade Rock Sliders For 4x4
Rock sliders are a common item on 4WD vehicles. They protect your rocker panels from damage, both to themselves and the vehicle body. Rock sliders commonly get damaged offroad by sticks, stones, and debris. Having custom rock sliders installed can prevent all of these issues. Here we are talking about the best way to make homemade rock sliders for your 4x4. If you're going to build them yourself, it's better to follow this detailed step-by-step instruction.
DIY Rock Slider And Scrub Rails
Cut two long pieces of metal for the slider and some braces that will go in-between the two long pieces. Cut two more details from the tube for the leg of the slider. Now, cut and assemble two I clamps from the flat bar. This will be the mount point for your new fender scrub rails. Cut out a top rail long enough to attach to your tailgate and several small braces for connecting to the bottom of your fence under the bumper. Now, you can transfer to hard-to-access areas without the risk of damaging your vehicle.
How To Build Easy DIY Rock Sliders
Building rock sliders is something fun and challenging. This project can be done anywhere as long as you have the right tools and skills. By building rock sliders, you will enhance your four-wheeler's capabilities by allowing it to ride over rocks and other obstacles that could otherwise damage the machine. A rock slider also helps get over logs or any other natural formations in the ground you may encounter when riding your four-wheeler.
How To DIY Rock Sliders
To make a rock slider, start by having the truck prepped and leveled. Mount the shocks, shock mounts, and springs correctly. Now, cut out the body in the area where you want the slider to go, and weld it in place. After that's all done, take the steel brackets, drill holes in them, mount them on one end of the slider with bolts and washers, then repeat on the other side. Finally, mount it to the vehicle with some more bolts and washers. The metal rods hold your wheels in the place closest to them.
DIY Custom Rock Sliders
Rock sliders are solid and sturdy frames attached to the body of a car. They protect the underbody from rocks and other objects present on the ground. The DIY custom rock slider uses flat metal bars, rods, and welding tools. Cut a long rod for the outer part and smaller rods for the connecting pieces. Weld everything together, and you will have a rock-solid frame. For you to be able to fix this frame onto your car, you need to make a U-shaped tube from the flat bar.
DIY Wrangler Jeep Rock Slider
You can make this unique rock slider for your Jeep Wrangler and get more fun in off-roading. It is made from a flat metal bar and square tubing. You have to cut them into pieces and assemble them for welding. Install it on a non-factory rock railing to slide on the rocks easier. Now you are ready to upgrade your vehicle and make your off-roading experience more fun. This Jeep Rock Slider comes with all the bushings and bolts necessary to weld on a new front rock slider.
How To Build Rock Sliders
Rock sliders are a great accessory to help your Sportage move safely over rocks and any other common obstacle. It's super easy to put your rock slider together. The metal rods are used for the actual tick slider, while the metal square tubing is used to squeeze the rock slider perfectly. Assemble the legs first before attaching them to your car or truck, especially if you need to make any adjustments. The process is relatively simple. You need metal rods and square tubing for framing and some sturdy bolts for mounting.
How To Make A Simple Set Of Rock Sliders
You will need to chop off the welded on tabs from the frame and add a welded on corner flange for this project. Each side will require two steel tubes cut about 12 inches each. The flat part of the tubing should be about 3 inches wide and 4 inches long. A straight edge will be required to get an excellent cut for the flat bar/plate for the other side of the rock slider. This article will walk you through a basic design using a flat bar with welded tube ends and a simple paint job.
